Doc: Removed references to embedded Android

The commit also includes minor language edits.

Change-Id: I641452dae29cafdbfe8846d5fc1a7d8302d257d8
Task-number: QTEE-922
Reviewed-by: Topi Reiniö <topi.reinio@theqtcompany.com>

1 files changed, 0 insertions, 105 deletions

diff --git a/src/doc/src/devices/qtee-nexus-7.qdoc b/src/doc/src/devices/qtee-nexus-7.qdoc
deleted file mode 100644
index 54ba445..0000000
--- a/src/doc/src/devices/qtee-nexus-7.qdoc
+++ /dev/null
@@ -1,105 +0,0 @@
-/****************************************************************************
-**
-** Copyright (C) 2014 Digia Plc
-** All rights reserved.
-** For any questions to Digia, please use the contact form at
-** http://www.qt.io
-**
-** This file is part of Qt Enterprise Embedded.
-**
-** Licensees holding valid Qt Enterprise licenses may use this file in
-** accordance with the Qt Enterprise License Agreement provided with the
-** Software or, alternatively, in accordance with the terms contained in
-** a written agreement between you and Digia.
-**
-** If you have questions regarding the use of this file, please use
-** the contact form at http://www.qt.io
-**
-****************************************************************************/
-/*!
-    \target Nexus 7 (2012/2013) (embedded Android)
-    \page qtee-preparing-hardware-nexus-7.html
-    \title Preparing Nexus 7 (2012/2013)
-    \previouspage qtee-installation-guide.html
-    \nextpage qtee-building-and-running.html
-
-    Take the following steps to prepare a
-    \l{http://www.google.com/nexus/7/specs/}{Nexus 7 (2012/2013)} for
-    \B2Q.
-
-    \note The installation process will wipe the device. Make sure to
-    backup any personal data. The device can later be restored to
-    factory state, see \l{nexus-factory-reset}{Troubleshooting}.
-
-    The Nexus 7 must have the same Android main version (e.g. \c{4.2}
-    or \c{4.4}) as the generic \B2Q eAndroid stack that is to be
-    installed. If needed, you can update the Android version either by
-    using Android's upgrading tool, or by flashing a factory image of
-    the right version. See \l{nexus-factory-reset}{Troubleshooting}.
-
-    \section1 Enabling Developer Mode
-
-    In order to install the \B2Q stack into the Nexus 7, you need to
-    enable developer mode and USB debugging. This is only needed for
-    the first time install.
-
-    \note If for some reason the device does not boot up normally, it
-    is also possible to install to a Nexus 7 started up in
-    \c{fastboot} (bootloader) mode (see
-    \l{nexus-factory-reset}{Troubleshooting}). Just skip this section
-    and add the \c{-fastboot} argument to the \c{deploy.sh} command
-    below.
-
-    \list 1
-        \li Power up the device.
-        \li Open the \b{Settings} app and select the \b{About tablet} item.
-        \li Press the \b{Build number} item seven times, until the message "You are now a developer!" appears.
-
-        \li Back in the \b{Settings} menu, select \b{Developer options}.
-        \li Press the \b{USB debugging} item and confirm that you allow USB debugging.
-    \endlist
-
-    You should now be able to establish USB connection to the device as follows.
-
-    \section1 Setting up USB Access
-
-    \include b2qt-post-install-setup.qdocinc setting up usb access
-
-    \section1 Deploying the \B2Q Stack
-
-    \include common.qdocinc wizard
-
-    Depending on the edition of your Nexus 7 device, use one of the
-    commands below to install the \B2Q stack. Replace \c{X.Y} with the
-    device's Android version number, for example \c{4.2} or \c{4.4}.
-
-    \note The deploy script will check that the connected Nexus device
-    is of the expected type and Android version, and abort the
-    installation if it is not.
-
-    \list
-        \li \b{Nexus 7 (2013):}
-        \badcode
-            cd <INSTALL_DIR>
-            ./Boot2Qt-4.x/generic-X.Y-eAndroid/images/nexus7v2/deploy.sh
-        \endcode
-        \li \b{Nexus 7 (2012):}
-        \badcode
-            cd <INSTALL_DIR>
-            ./Boot2Qt-4.x/generic-X.Y-eAndroid/images/nexus7/deploy.sh
-        \endcode
-    \endlist
-
-    During the installation, the device may ask for confirmation to be
-    unlocked. Press the power button once to confirm.
-
-    The device will reboot during the process. Do not interact with it
-    or unplug it until the process is fully completed.
-
-    \section1 Configuring a Device Kit in Qt Creator
-
-    \include b2qt-post-install-setup.qdocinc configuring device kit android
-
-    You are now ready to start developing for your device. For more information,
-    see \l{Building and Running an Example}.
-*/