diff options
author | Samuli Piippo <samuli.piippo@digia.com> | 2013-10-11 11:46:45 +0300 |
---|---|---|
committer | Samuli Piippo <samuli.piippo@digia.com> | 2013-10-14 08:39:29 +0300 |
commit | 7281b8851573c325a72da008245d54e06516e2d2 (patch) | |
tree | 63481f2e0ca69ebfe8fa4a4df453eb582f4a9299 /src/doc | |
parent | 8b72d8990033af83b7b44871d5af3e61c965fc72 (diff) |
Doc: Add documentation for raspberry Pi
Change-Id: If57154ba74595a1f52802d81908d333924319e7d
Reviewed-by: Topi Reiniƶ <topi.reinio@digia.com>
Reviewed-by: Eirik Aavitsland <eirik.aavitsland@digia.com>
Diffstat (limited to 'src/doc')
-rw-r--r-- | src/doc/src/b2qt-post-install-setup.qdocinc | 24 | ||||
-rw-r--r-- | src/doc/src/b2qt.qdoc | 69 |
2 files changed, 93 insertions, 0 deletions
diff --git a/src/doc/src/b2qt-post-install-setup.qdocinc b/src/doc/src/b2qt-post-install-setup.qdocinc index 4733aa8..8d1a58c 100644 --- a/src/doc/src/b2qt-post-install-setup.qdocinc +++ b/src/doc/src/b2qt-post-install-setup.qdocinc @@ -41,6 +41,7 @@ To do so, connect your device to your computer via USB and launch Qt Creator (\B2Q IDE). Then, +//! [steps for device kit] \list 1 \li Go to \b{Tools > Options > Build & Run > Kits} \li Select one of the predefined Kits starting with \e{Boot2Qt...} @@ -48,5 +49,28 @@ \li Select the correct device in the \b{Device} combobox. \li Click \b{Ok}. \endlist +//! [steps for device kit] //! [configuring device kit] + +//! [configuring network device] + After the hardware has been prepared, there are final steps required + to set up the development tools in Qt Creator for your device. + + To do so, connect your device to network via ethernet cable and launch + Qt Creator (\B2Q IDE). Then, + + \list 1 + \li Go to \b{Tools > Options > Devices} + \li Click \b{Add...} + \li Select \b{Boot2Qt Device} and Click \b{Start Wizart} + \li Fill in name of the device and network address. Device address can be seen from + \e{Launcher Settings} when device is running \B2Q demo + \li Click \b{Finish}. + \endlist + + You also have to configure the right device to be used for each \b{Kit}. + + \include b2qt-post-install-setup.qdocinc steps for device kit + +//! [configuring network device] */ diff --git a/src/doc/src/b2qt.qdoc b/src/doc/src/b2qt.qdoc index 341dfac..2489a54 100644 --- a/src/doc/src/b2qt.qdoc +++ b/src/doc/src/b2qt.qdoc @@ -33,6 +33,7 @@ \li \l{Preparing Nexus 7}{Nexus 7 (embedded Android)} \li \l{Preparing Sabre Lite i.MX 6}{Sabre Lite i.MX 6 (embedded Android)} \li \l{Preparing BeagleBoard-xM}{BeagleBoard-xM (embedded Android and Linux)} + \li \l{Preparing Raspberry Pi}{Raspberry Pi (embedded Linux)} \endlist \li \b {\l{Building and Running an Example}} \li \b {\l{Customization}} @@ -232,6 +233,7 @@ \li \l{Nexus 7 (embedded Android)} \li \l{Sabre Lite i.MX 6 (embedded Android)} \li \l{BeagleBoard-xM (embedded Android and Linux)} + \li \l{Raspberry Pi (embedded Linux)} \endlist If you are only using the emulator, you can skip this step @@ -542,6 +544,73 @@ */ /*! + \target Raspberry Pi (embedded Linux) + \page b2qt-preparing-hardware-rasberrypi.html + \title Preparing Raspberry Pi + \previouspage b2qt-installation-guide.html + \nextpage b2qt-building-and-running.html + + When using a \l{http://www.raspberrypi.org/}{Raspberry Pi} as a + development device, following steps are required to prepare it for + \B2Q. + + \note \b{It is important that the steps in this section are repeated + every time after updating the \B2Q SDK.} + + The images containing \B2Q stack for Raspberry Pi is included in the SDK, + ready to be copied to a micro-SD card. + + \section1 Preparing a Micro-SD Card + + For \B2QL, a card of at least 512MB capacity is sufficient. + + Plug the micro-SD card/reader into the development host PC and use + the following command to find out its device path + (i.e. \c{/dev/XXX}, where \c{XXX} typically is \c{sdb}): + + \code + df -h + \endcode + + Alternatively, if the micro-SD card is unformatted, run the following + command immediately after inserting the card to see its device + path: + + \code + dmesg | tail + \endcode + + Now make sure the micro-SD card is not mounted: + + \code + umount /dev/XXX + \endcode + + \section1 Installing the \B2Q Image + + Write the image to the micro-SD card: + + \code + cd <SDK_INSTALL_DIR> + Boot2Qt-1.0/raspberrypi-eLinux/images/deploy.sh /dev/XXX + \endcode + + \warning \b{Make very sure you select the right device. Selecting the wrong + one can result in a wiped hard drive}. + + After the image has been deployed, power up the device and confirm that it shows + a \B2Q welcome screen and/or demo. + + \section1 Configuring a Device Kit in Qt Creator + + \include b2qt-post-install-setup.qdocinc configuring network device + + \b {You are now ready to start developing for your device!} + + See \l{Building and Running an Example} +*/ + +/*! \page b2qt-building-and-running.html \title Building and Running an Example \previouspage b2qt-installation-guide.html |