summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--src/doc/src/b2qt.qdoc86
1 files changed, 84 insertions, 2 deletions
diff --git a/src/doc/src/b2qt.qdoc b/src/doc/src/b2qt.qdoc
index e2322de..1b29b5a 100644
--- a/src/doc/src/b2qt.qdoc
+++ b/src/doc/src/b2qt.qdoc
@@ -45,6 +45,7 @@
\list
\li \l{Preparing Nexus 7}{Nexus 7 (2012) (embedded Android)}
\li \l{Preparing Sabre Lite i.MX 6}{Sabre Lite i.MX 6 (embedded Android and Linux)}
+ \li \l{Preparing BeagleBone Black}{BeagleBone Black (embedded Android and Linux)}
\li \l{Preparing BeagleBoard-xM}{BeagleBoard-xM (embedded Linux)}
\li \l{Preparing Raspberry Pi}{Raspberry Pi Model B (embedded Linux)}
\endlist
@@ -277,6 +278,7 @@
\list
\li \l{Nexus 7 (2012) (embedded Android)}
\li \l{Sabre Lite i.MX 6 (embedded Android and Linux)}
+ \li \l{BeagleBone Black (embedded Android and Linux)}
\li \l{BeagleBoard-xM (embedded Linux)}
\li \l{Raspberry Pi Model B (embedded Linux)}
\endlist
@@ -524,7 +526,7 @@
\endcode
\endlist
- After the installation is complete, power on the device and check that
+ After the installation is complete, insert the SD card, power on the device and check that
the \B2Q welcome screen and/or demo appear.
\section1 Setting up USB Access
@@ -575,7 +577,7 @@
sudo Boot2Qt-2.x/raspberrypi-eLinux/images/deploy.sh /dev/<device_name>
\endcode
- After the image has been deployed, power on the device and check that
+ After the image has been deployed, insert the SD card, power on the device and check that
the \B2Q welcome screen and/or demo appear.
\section1 Configuring a Device Kit in Qt Creator
@@ -587,6 +589,85 @@
*/
/*!
+ \target BeagleBone Black (embedded Android and Linux)
+ \page qtee-preparing-hardware-beaglebone.html
+ \title Preparing BeagleBone Black
+ \previouspage qtee-installation-guide.html
+
+ Take the following steps to prepare a
+ \l{http://beagleboard.org/products/beaglebone%20black}{BeagleBone Black} for \B2Q.
+
+ \note It is important that you repeat the steps in this section after you
+ update \SDK.
+
+ The images containing the \B2Q stack for BeagleBone Black are included
+ in \SDK, ready to be copied to an SD card.
+
+ \section1 Preparing an SD Card
+
+ For \B2QA, an SD card of at least 2 GB capacity is needed. For \B2QL,
+ a card of at least 512 MB capacity is sufficient.
+
+ \include detect-sd-card-device-name.qdocinc instructions
+
+ \section1 Installing the Android image
+
+ \e{If installing} \B2QL, \e{you can skip this step and proceed to}
+ \l{Installing the Boot to Qt Image}.
+
+ Download the package \e{TI_Android_JB_4.2.2_DevKit_4.1.1_beagleboneblack.tar.gz} from
+ \l{http://downloads.ti.com/sitara_android/esd/TI_Android_DevKit/TI_Android_JB_4_2_2_DevKit_4_1_1/index_FDS.html}
+ {Texas Instruments} (search for \e {BeagleBone Black} in the list of download packages).
+
+ Use the following commands to create an SD card containing the
+ downloaded image:
+
+ \list 1
+ \li Extract the downloaded package:
+ \code
+ ~$ tar zxvf ~/Downloads/TI_Android_JB_4.2.2_DevKit_4.1.1_beagleboneblack.tar.gz
+ \endcode
+ \li Run beagleboneblack/mkmmc-android.sh:
+ \code
+ ~$ cd beagleboneblack
+ ~/beagleboneblack$ sudo ./mkmmc-android.sh /dev/<device_name>
+ \endcode
+ \endlist
+
+ \section1 Installing the \B2Q Image
+
+ Then, upgrade the SD card with \B2Q. Use one of the commands below,
+ depending on whether you are developing for embedded Android or Linux:
+
+ \list
+ \li \b{\B2QA}
+ \code
+ cd <INSTALL_DIR>
+ ./Boot2Qt-2.x/beaglebone-eAndroid/images/deploy.sh /dev/<device_name>
+ \endcode
+ \li \b{\B2QL}
+ \code
+ cd <INSTALL_DIR>
+ sudo ./Boot2Qt-2.x/beaglebone-eLinux/images/deploy.sh /dev/<device_name>
+ \endcode
+ \endlist
+
+ After the installation is complete, insert the SD card, power on the device and check that
+ the \B2Q welcome screen and/or demo appear.
+
+ \section1 Setting up USB Access
+
+ \include b2qt-post-install-setup.qdocinc setting up usb access
+
+ \section1 Configuring a Device Kit in Qt Creator
+
+ \include b2qt-post-install-setup.qdocinc configuring device kit
+
+ You are now ready to start developing for your device. For more information,
+ see \l{Building and Running an Example}.
+*/
+
+/*!
\page qtee-building-and-running.html
\title Building and Running an Example
\previouspage qtee-preparing-hardware.html
@@ -756,6 +837,7 @@
\list
\li \l{http://www.google.com/nexus/7/specs/}{Google/Asus Nexus 7 (2012)}
\li \l{http://beagleboard.org/hardware-xM}{BeagleBoard-xM}
+ \li \l{http://beagleboard.org/products/beaglebone%20black}{BeagleBone Black}
\li \l{http://boundarydevices.com/products/sabre-lite-imx6-sbc/}{Freescale i.MX6 Sabre Lite board (Boundary Devices)}
\li \l{http://www.raspberrypi.org/faqs}{Raspberry Pi Model B}
\endlist