summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--src/doc/src/b2qt.qdoc37
1 files changed, 25 insertions, 12 deletions
diff --git a/src/doc/src/b2qt.qdoc b/src/doc/src/b2qt.qdoc
index 03a1c75..1822921 100644
--- a/src/doc/src/b2qt.qdoc
+++ b/src/doc/src/b2qt.qdoc
@@ -31,7 +31,7 @@
\li \l{Preparing Hardware}
\list
\li \l{Preparing Nexus 7}{Nexus 7 (embedded Android)}
- \li \l{Preparing Sabre Lite i.MX 6}{Sabre Lite i.MX 6 (embedded Android)}
+ \li \l{Preparing Sabre Lite i.MX 6}{Sabre Lite i.MX 6 (embedded Android and Linux)}
\li \l{Preparing BeagleBoard-xM}{BeagleBoard-xM (embedded Android and Linux)}
\li \l{Preparing Raspberry Pi}{Raspberry Pi Model B (embedded Linux)}
\endlist
@@ -228,7 +228,7 @@
\list
\li \l{Nexus 7 (embedded Android)}
- \li \l{Sabre Lite i.MX 6 (embedded Android)}
+ \li \l{Sabre Lite i.MX 6 (embedded Android and Linux)}
\li \l{BeagleBoard-xM (embedded Android and Linux)}
\li \l{Raspberry Pi Model B (embedded Linux)}
\endlist
@@ -408,7 +408,7 @@
*/
/*!
- \target Sabre Lite i.MX 6 (embedded Android)
+ \target Sabre Lite i.MX 6 (embedded Android and Linux)
\page qee-preparing-hardware-imx6.html
\title Preparing Sabre Lite i.MX 6
\previouspage qee-installation-guide.html
@@ -416,22 +416,26 @@
When using a
\l{http://boundarydevices.com/products/sabre-lite-imx6-sbc/}{Sabre
Lite i.MX 6} as a development device, following steps are required
- to prepare it for \B2QA.
+ to prepare it for \B2Q.
\note \b{It is important that the steps in this section are repeated
every time after updating \SDK.}
- The images containing \B2Q stack for Sabre Lite i.MX 6 is included in the SDK,
- ready to be copied to a micro-SD card.
+ The images containing the \B2Q stack for Sabre Lite i.MX 6 are included
+ in the SDK, ready to be copied to a micro-SD card.
\section1 Preparing a Micro-SD Card
- For \B2QA, a micro-SD card of at least 4GB capacity is needed.
+ For \B2QA, a micro-SD card of at least 4GB capacity is needed. For \B2QL,
+ a card of at least 512MB capacity is sufficient.
\include detect-sd-card-device-name.qdocinc instructions
\section1 Installing the Android image
+ \e{If installing} \B2QL, \e{you can skip this step and proceed to}
+ \l{Installing the Boot to Qt Image}.
+
Download the package \e{imx6-jb-20130628.tar.gz} from
\l{http://boundarydevices.com/android-jellybean-on-i-mx6-with-no-disclaimers/}{Boundary
Devices Android Jellybean i.MX6 images} (registration required).
@@ -461,12 +465,21 @@
sudo apt-get install u-boot-tools
\endcode
- Then, upgrade the micro-SD Card with \B2QA:
+ Then, upgrade the micro-SD Card with \B2Q. Use one of the commands below,
+ depending on whether you're developing for embedded Android or Linux:
- \code
- cd <INSTALL_DIR>
- Boot2Qt-1.0/iMX6-eAndroid/images/deploy.sh /dev/XXX
- \endcode
+ \list
+ \li \b{\B2QA}
+ \code
+ cd <INSTALL_DIR>
+ Boot2Qt-1.0/iMX6-eAndroid/images/deploy.sh /dev/XXX
+ \endcode
+ \li \b{\B2QL}
+ \code
+ cd <INSTALL_DIR>
+ Boot2Qt-1.0/iMX6-eLinux/images/deploy.sh /dev/XXX
+ \endcode
+ \endlist
After the installation is complete, power up the device and confirm that it shows
a \B2Q welcome screen and/or demo.