diff options
Diffstat (limited to 'src/doc/src/devices/qtee-bd-sl-imx6.qdoc')
| -rw-r--r-- | src/doc/src/devices/qtee-bd-sl-imx6.qdoc | 137 |
1 files changed, 0 insertions, 137 deletions
diff --git a/src/doc/src/devices/qtee-bd-sl-imx6.qdoc b/src/doc/src/devices/qtee-bd-sl-imx6.qdoc deleted file mode 100644 index 6aa39ac..0000000 --- a/src/doc/src/devices/qtee-bd-sl-imx6.qdoc +++ /dev/null @@ -1,137 +0,0 @@ -/**************************************************************************** -** -** Copyright (C) 2014 Digia Plc -** All rights reserved. -** For any questions to Digia, please use the contact form at -** http://www.qt.io -** -** This file is part of Qt Enterprise Embedded. -** -** Licensees holding valid Qt Enterprise licenses may use this file in -** accordance with the Qt Enterprise License Agreement provided with the -** Software or, alternatively, in accordance with the terms contained in -** a written agreement between you and Digia. -** -** If you have questions regarding the use of this file, please use -** the contact form at http://www.qt.io -** -****************************************************************************/ -/*! - \page qtee-preparing-hardware-imx6.html - \title Boundary Devices i.MX6 Boards - \previouspage qtee-installation-guide.html - - Take the following steps when preparing these boards for \B2Q: - - \list - \li \l{http://boundarydevices.com/products/sabre-lite-imx6-sbc/} - {Boundary Devices BD-SL-i.MX6 (SABRE Lite)} - \li \l{http://boundarydevices.com/product/nitrogen6x-copy/} - {Boundary Devices Nitrogen6X} - \li \l{http://boundarydevices.com/product/nitrogen6_lite/} - {Boundary Devices Nitrogen6_Lite} - \li \l{http://boundarydevices.com/product/nitrogen6max/} - {Boundary Devices Nitrogen6_MAX} - \li \l{http://boundarydevices.com/product/nitrogen6x-som/} - {Boundary Devices Nitrogen6X_SOM} - \endlist - - \note It is important that you repeat the steps in this section after you - update \SDK. - - The images containing the \B2Q stack for the device are included - in \SDK, ready to be copied to an SD card. - - \section1 Preparing an SD Card - - For \B2QL, an SD card of at least 1 GB capacity is needed. - - \include detect-sd-card-device-name.qdocinc instructions - - \section1 Installing the \B2Q Image - - \include common.qdocinc wizard - - Make sure you have the required tools installed in your development machine: - - \badcode - sudo apt-get install u-boot-tools - \endcode - - Then, upgrade the SD card with \B2Q. First, ensure that no partitions on the - SD card are mounted: - - \include detect-sd-card-device-name.qdocinc unmount - - Then, use the following command to install the embedded Linux image: - - \badcode - cd <INSTALL_DIR> - sudo dd bs=4k if=5.6/Boot2Qt/nitrogen6x/images/b2qt-embedded-qt5-image-nitrogen6x.img of=/dev/<device_name> - \endcode - - After the installation is complete, insert the SD card, power on the device and check that - the \B2Q welcome screen and/or demo appear. - - \b {Updating U-Boot} - - If you are updating from an older image, you may also need to update the version of U-Boot on the device. - The prebuilt image already contains U-Boot versions for most of the device variants from Boundary Devices, - but the update needs to be done manually when first starting the device. Correct device type is selected by - setting the \c uboot_defconfig U-Boot environment variable. More information available from - \l{https://boundarydevices.com/compiling-latest-u-boot-for-i-mx6-2015-edition/}{Boundary Devices}. - - Access the device's console and run the following commands on the U-Boot prompt: - - \badcode - setenv uboot_defconfig <device type> - run upgradeu - \endcode - - Reset or power cycle the device to start the new U-Boot. - To reset the U-Boot environment to new default values, enter the following commands - in the U-Boot command line - - \badcode - env default -a - saveenv - \endcode - - \b {Setup for Nitrogen6_Lite Device} - - The boot script requires the environment variables, \c dtbname and \c gpumem, to identify - the device as Nitrogen6_Lite. Otherwise, the device is booted with the default GPU - memory setting of 512MiB, which is more than what is available on the Nitrogen_Lite devices - (128MibB). - - Use one of the two following options to enable the scripts boot the device - with correct GPU memory setting: - - \list - \li Write a \c uEnv.txt file on to the boot partition of SD card with the following - content: - - \badcode - gpumem=67108864 - dtbname=imx6dl-nit6xlite.dtb - \endcode - - \li Access the device's console and run the following commands on the U-Boot prompt: - \badcode - U-Boot > setenv gpumem 67108864 - U-Boot > setenv dtbname imx6dl-nit6xlite.dtb - U-Boot > saveenv - \endcode - \endlist - - \section1 Setting up USB Access - - \include b2qt-post-install-setup.qdocinc setting up usb access - - \section1 Configuring a Device Kit in Qt Creator - - \include b2qt-post-install-setup.qdocinc configuring device kit linux - - You are now ready to start developing for your device. For more information, - see \l{Building and Running an Example}. -*/ |