1 files changed, 0 insertions, 88 deletions
diff --git a/src/doc/src/devices/qtee-kontron-smarc-samx6i.qdoc b/src/doc/src/devices/qtee-kontron-smarc-samx6i.qdoc
deleted file mode 100644
index f64b264..0000000
--- a/src/doc/src/devices/qtee-kontron-smarc-samx6i.qdoc
+++ /dev/null
@@ -1,88 +0,0 @@
-/****************************************************************************
-**
-** Copyright (C) 2014 Digia Plc
-** All rights reserved.
-** For any questions to Digia, please use the contact form at
-** http://www.qt.io
-**
-** This file is part of Qt Enterprise Embedded.
-**
-** Licensees holding valid Qt Enterprise licenses may use this file in
-** accordance with the Qt Enterprise License Agreement provided with the
-** Software or, alternatively, in accordance with the terms contained in
-** a written agreement between you and Digia.
-**
-** If you have questions regarding the use of this file, please use
-** the contact form at http://www.qt.io
-**
-****************************************************************************/
-/*!
-    \keyword Kontron SMARC-sAMX6i
-    \page qtee-preparing-hardware-smarc-samx6i.html
-    \title Preparing Kontron SMARC-sAMX6i
-    \previouspage qtee-installation-guide.html
-
-    Take the following steps to prepare a
-    \l{http://www.kontron.com/products/boards-and-standard-form-factors/smarc/smarc-samx6i.html}
-    {Kontron SMARC-sAMX6i} for \B2Q.
-
-    \note It is important that you repeat the steps in this section after you
-    update \SDK.
-
-    The images containing the \B2Q stack for Kontron SMARC-sAMX6i are included
-    in \SDK, ready to be copied to an SD card.
-
-    \section1 Preparing an SD Card
-
-    An SD card of at least 1 GB capacity is sufficient.
-
-    \include detect-sd-card-device-name.qdocinc instructions
-
-    \section1 Installing the \B2Q Image
-
-    \include common.qdocinc wizard
-
-    To write the image to the SD card, ensure that no partitions on the
-    SD card are mounted:
-
-    \include detect-sd-card-device-name.qdocinc unmount
-
-    Then,
-
-    \badcode
-        cd <INSTALL_DIR>
-        sudo dd bs=4k if=5.7/Boot2Qt/smarc-samx6i/images/b2qt-embedded-qt5-image-smarc-samx6i.img of=/dev/<device_name>
-    \endcode
-
-    By default, the Kontron SMARC-sAMX6i boots from its internal eMMC. In order to boot from
-    the external SD card, the U-Boot environment needs to be updated. Connect a serial cable
-    to the device and enter into the U-Boot environment by pressing any key before the autoboot.
-    Enter following commands into U-Boot:
-
-    \badcode
-        setenv mmcdev 1
-        setenv mmcpart 2
-        setenv bootcmd 'mmc dev ${mmcdev}; if mmc rescan; then if run loadfdt; then if run loaduimage; then run mmcboot; else run netboot; fi; else run netboot; fi; else run netboot; fi;'
-        setenv uimage /boot/uImage
-        setenv fdtfile /boot/imx6q-smx6-lcd.dtb
-        setenv mmcroot /dev/mmcblk2p2 rootwait rw
-        setenv mmcargs 'setenv bootargs video=mxcfb0:dev=hdmi,1280x720M@60,if=RGB24 fbmem=28M console=${console},${baudrate} root=${mmcroot}'
-        saveenv
-    \endcode
-
-    New U-Boot commands are now stored into the device, and you can start \B2Q.
-
-    After the image has been deployed, insert the SD card, power on the device and check that
-    the \B2Q welcome screen and/or demo appear.
-
-    \section1 Setting up USB Access
-
-    \include b2qt-post-install-setup.qdocinc setting up usb access
-
-    \section1 Configuring a Device Kit in Qt Creator
-
-    \include b2qt-post-install-setup.qdocinc configuring device kit
-
-    You are now ready to start developing for your device. For more information,
-    see \l{Building and Running an Example}.
-*/