diff options
Diffstat (limited to 'src/doc/src/devices/qtee-nexus-7.qdoc')
-rw-r--r-- | src/doc/src/devices/qtee-nexus-7.qdoc | 105 |
1 files changed, 0 insertions, 105 deletions
diff --git a/src/doc/src/devices/qtee-nexus-7.qdoc b/src/doc/src/devices/qtee-nexus-7.qdoc deleted file mode 100644 index 54ba445..0000000 --- a/src/doc/src/devices/qtee-nexus-7.qdoc +++ /dev/null @@ -1,105 +0,0 @@ -/**************************************************************************** -** -** Copyright (C) 2014 Digia Plc -** All rights reserved. -** For any questions to Digia, please use the contact form at -** http://www.qt.io -** -** This file is part of Qt Enterprise Embedded. -** -** Licensees holding valid Qt Enterprise licenses may use this file in -** accordance with the Qt Enterprise License Agreement provided with the -** Software or, alternatively, in accordance with the terms contained in -** a written agreement between you and Digia. -** -** If you have questions regarding the use of this file, please use -** the contact form at http://www.qt.io -** -****************************************************************************/ -/*! - \target Nexus 7 (2012/2013) (embedded Android) - \page qtee-preparing-hardware-nexus-7.html - \title Preparing Nexus 7 (2012/2013) - \previouspage qtee-installation-guide.html - \nextpage qtee-building-and-running.html - - Take the following steps to prepare a - \l{http://www.google.com/nexus/7/specs/}{Nexus 7 (2012/2013)} for - \B2Q. - - \note The installation process will wipe the device. Make sure to - backup any personal data. The device can later be restored to - factory state, see \l{nexus-factory-reset}{Troubleshooting}. - - The Nexus 7 must have the same Android main version (e.g. \c{4.2} - or \c{4.4}) as the generic \B2Q eAndroid stack that is to be - installed. If needed, you can update the Android version either by - using Android's upgrading tool, or by flashing a factory image of - the right version. See \l{nexus-factory-reset}{Troubleshooting}. - - \section1 Enabling Developer Mode - - In order to install the \B2Q stack into the Nexus 7, you need to - enable developer mode and USB debugging. This is only needed for - the first time install. - - \note If for some reason the device does not boot up normally, it - is also possible to install to a Nexus 7 started up in - \c{fastboot} (bootloader) mode (see - \l{nexus-factory-reset}{Troubleshooting}). Just skip this section - and add the \c{-fastboot} argument to the \c{deploy.sh} command - below. - - \list 1 - \li Power up the device. - \li Open the \b{Settings} app and select the \b{About tablet} item. - \li Press the \b{Build number} item seven times, until the message "You are now a developer!" appears. - - \li Back in the \b{Settings} menu, select \b{Developer options}. - \li Press the \b{USB debugging} item and confirm that you allow USB debugging. - \endlist - - You should now be able to establish USB connection to the device as follows. - - \section1 Setting up USB Access - - \include b2qt-post-install-setup.qdocinc setting up usb access - - \section1 Deploying the \B2Q Stack - - \include common.qdocinc wizard - - Depending on the edition of your Nexus 7 device, use one of the - commands below to install the \B2Q stack. Replace \c{X.Y} with the - device's Android version number, for example \c{4.2} or \c{4.4}. - - \note The deploy script will check that the connected Nexus device - is of the expected type and Android version, and abort the - installation if it is not. - - \list - \li \b{Nexus 7 (2013):} - \badcode - cd <INSTALL_DIR> - ./Boot2Qt-4.x/generic-X.Y-eAndroid/images/nexus7v2/deploy.sh - \endcode - \li \b{Nexus 7 (2012):} - \badcode - cd <INSTALL_DIR> - ./Boot2Qt-4.x/generic-X.Y-eAndroid/images/nexus7/deploy.sh - \endcode - \endlist - - During the installation, the device may ask for confirmation to be - unlocked. Press the power button once to confirm. - - The device will reboot during the process. Do not interact with it - or unplug it until the process is fully completed. - - \section1 Configuring a Device Kit in Qt Creator - - \include b2qt-post-install-setup.qdocinc configuring device kit android - - You are now ready to start developing for your device. For more information, - see \l{Building and Running an Example}. -*/ |