1 files changed, 0 insertions, 106 deletions
diff --git a/src/doc/src/devices/qtee-toradex-apalis.qdoc b/src/doc/src/devices/qtee-toradex-apalis.qdoc
deleted file mode 100644
index 84fa350..0000000
--- a/src/doc/src/devices/qtee-toradex-apalis.qdoc
+++ /dev/null
@@ -1,106 +0,0 @@
-/****************************************************************************
-**
-** Copyright (C) 2014 Digia Plc
-** All rights reserved.
-** For any questions to Digia, please use the contact form at
-** http://www.qt.io
-**
-** This file is part of Qt Enterprise Embedded.
-**
-** Licensees holding valid Qt Enterprise licenses may use this file in
-** accordance with the Qt Enterprise License Agreement provided with the
-** Software or, alternatively, in accordance with the terms contained in
-** a written agreement between you and Digia.
-**
-** If you have questions regarding the use of this file, please use
-** the contact form at http://www.qt.io
-**
-****************************************************************************/
-/*!
-    \keyword Toradex Apalis iMX6
-    \page qtee-preparing-hardware-apalis-imx6.html
-    \title Preparing Toradex Apalis iMX6
-    \previouspage qtee-installation-guide.html
-
-    Take the following steps to prepare a
-    \l{http://www.toradex.com/products/apalis-arm-computer-modules/freescale-imx-6-computer-module}
-    {Toradex Apalis iMX6} for \B2Q.
-
-    \note It is important that you repeat the steps in this section after you
-    update \SDK.
-
-    The images containing the \B2Q stack for Toradex Apalis iMX6 are included
-    in \SDK, ready to be copied to an SD card.
-
-    \section1 Preparing an SD Card
-
-    An SD card of at least 1 GB capacity is sufficient.
-
-    \include detect-sd-card-device-name.qdocinc instructions
-
-    \section1 Installing the \B2Q Image
-
-    \include common.qdocinc wizard
-
-    To write the image to the SD card, ensure that no partitions on the
-    SD card are mounted:
-
-    \include detect-sd-card-device-name.qdocinc unmount
-
-    Then,
-
-    \badcode
-        cd <INSTALL_DIR>
-        sudo dd bs=4k if=5.7/Boot2Qt/apalis-imx6/images/b2qt-embedded-qt5-image-apalis-imx6.img of=/dev/<device_name>
-    \endcode
-
-    By default, the Toradex Apalis iMX6 boots from its internal eMMC. In order to boot from
-    the external SD card, the U-Boot needs to be updated. Connect a serial cable
-    to the device and enter into the U-Boot environment by pressing any key before the autoboot.
-    Enter following commands into U-Boot:
-
-    \badcode
-        setenv drive 2
-        setenv setupdate 'fatload mmc ${drive}:1 ${loadaddr} flash_mmc.img; source'
-
-        run setupdate
-        run update_uboot
-    \endcode
-
-    Reset or power cycle the device to start the new U-Boot.
-    To reset the U-Boot environment to new default values, enter the following commands
-    in the U-Boot command line
-
-    \badcode
-        env default -a
-        saveenv
-    \endcode
-
-
-    New U-Boot commands are now stored into the device, and you can start \B2Q. For more information
-    about the boot process on Toredex Apalis iMX6, see
-    \l{http://developer.toradex.com/software-resources/arm-family/linux/linux-booting}{Toradex Linux Booting}.
-
-    After the image has been deployed, insert the SD card, power on the device and check that
-    the \B2Q welcome screen and/or demo appear.
-
-    \section1 Setting up USB Access
-
-    The \e {Ixora Carrier Board} on Toradex Apalis iMX6 includes a USB 2.0 port
-    that can be used for an \c adb connection between the device and the
-    development host, provided it's configured for USB OTG. To enable USB OTG
-    connectivity, ensure that jumper JP2, located next to the USB ports, is open.
-
-    For more information, see datasheet for
-    \l{https://www.toradex.com/products/carrier-boards/ixora-carrier-board}
-    {Ixora Carrier Board}.
-
-    \include b2qt-post-install-setup.qdocinc setting up usb access
-
-    \section1 Configuring a Device Kit in Qt Creator
-
-    \include b2qt-post-install-setup.qdocinc configuring device kit
-
-    You are now ready to start developing for your device. For more information,
-    see \l{Building and Running an Example}.
-*/