/****************************************************************************
**
** Copyright (C) 2014 Digia Plc
** All rights reserved.
** For any questions to Digia, please use the contact form at
** http://www.qt.io
**
** This file is part of Qt Enterprise Embedded.
**
** Licensees holding valid Qt Enterprise licenses may use this file in
** accordance with the Qt Enterprise License Agreement provided with the
** Software or, alternatively, in accordance with the terms contained in
** a written agreement between you and Digia.
**
** If you have questions regarding the use of this file, please use
** the contact form at http://www.qt.io
**
****************************************************************************/
/*!
    \keyword Kontron SMARC-sAMX6i
    \page qtee-preparing-hardware-smarc-samx6i.html
    \title Preparing Kontron SMARC-sAMX6i
    \previouspage qtee-installation-guide.html

    Take the following steps to prepare a
    \l{http://www.kontron.com/products/boards-and-standard-form-factors/smarc/smarc-samx6i.html}
    {Kontron SMARC-sAMX6i} for \B2Q.

    \note It is important that you repeat the steps in this section after you
    update \SDK.

    The images containing the \B2Q stack for Kontron SMARC-sAMX6i are included
    in \SDK, ready to be copied to an SD card.

    \section1 Preparing an SD Card

    An SD card of at least 1 GB capacity is sufficient.

    \include detect-sd-card-device-name.qdocinc instructions

    \section1 Installing the \B2Q Image

    \include common.qdocinc wizard

    To write the image to the SD card, ensure that no partitions on the
    SD card are mounted:

    \include detect-sd-card-device-name.qdocinc unmount

    Then,

    \badcode
        cd <INSTALL_DIR>
        sudo dd bs=4k if=5.6/Boot2Qt/smarc-samx6i/images/b2qt-embedded-qt5-image-smarc-samx6i.img of=/dev/<device_name>
    \endcode

    By default, the Kontron SMARC-sAMX6i boots from its internal eMMC. In order to boot from
    the external SD card, the U-Boot environment needs to be updated. Connect a serial cable
    to the device and enter into the U-Boot environment by pressing any key before the autoboot.
    Enter following commands into U-Boot:

    \badcode
        setenv mmcdev 1
        setenv mmcpart 2
        setenv bootcmd 'mmc dev ${mmcdev}; if mmc rescan; then if run loadfdt; then if run loaduimage; then run mmcboot; else run netboot; fi; else run netboot; fi; else run netboot; fi;'
        setenv uimage /boot/uImage
        setenv fdtfile /boot/imx6q-smx6-lcd.dtb
        setenv mmcroot /dev/mmcblk2p2 rootwait rw
        setenv mmcargs 'setenv bootargs video=mxcfb0:dev=hdmi,1280x720M@60,if=RGB24 fbmem=28M console=${console},${baudrate} root=${mmcroot}'
        saveenv
    \endcode

    New U-Boot commands are now stored into the device, and you can start \B2Q.

    After the image has been deployed, insert the SD card, power on the device and check that
    the \B2Q welcome screen and/or demo appear.

    \section1 Setting up USB Access

    \include b2qt-post-install-setup.qdocinc setting up usb access

    \section1 Configuring a Device Kit in Qt Creator

    \include b2qt-post-install-setup.qdocinc configuring device kit

    You are now ready to start developing for your device. For more information,
    see \l{Building and Running an Example}.
*/