/****************************************************************************
**
** Copyright (C) 2014 Digia Plc
** All rights reserved.
** For any questions to Digia, please use the contact form at
** http://www.qt.io
**
** This file is part of Qt Enterprise Embedded.
**
** Licensees holding valid Qt Enterprise licenses may use this file in
** accordance with the Qt Enterprise License Agreement provided with the
** Software or, alternatively, in accordance with the terms contained in
** a written agreement between you and Digia.
**
** If you have questions regarding the use of this file, please use
** the contact form at http://www.qt.io
**
****************************************************************************/
/*!
    \keyword Toradex Colibri VF50 and VF61
    \page qtee-preparing-hardware-colibri-vf.html
    \title Preparing Toradex Colibri VF50 and VF61
    \previouspage qtee-installation-guide.html

    Take the following steps to prepare a
    \l{https://www.toradex.com/products/colibri-arm-computer-modules/freescale-vybrid-VF6xx-computer-module}
    {Toradex Colibri VF61} or
    \l{https://www.toradex.com/products/colibri-arm-computer-modules/freescale-vybrid-VF5xx-computer-module}
    {Toradex Colibri VF50} for \B2Q.

    \note It is important that you repeat the steps in this section after you
    update \SDK.

    The images containing the \B2Q stack for Toradex Colibri-VF devices are included
    in \SDK, ready to be copied to an SD card.

    \section1 Preparing an SD Card

    An SD card of at least 1 GB capacity is sufficient.

    \include detect-sd-card-device-name.qdocinc instructions

    \section1 Installing the \B2Q Image

    \include common.qdocinc wizard

    To write the image to the SD card, ensure that no partitions on the
    SD card are mounted:

    \include detect-sd-card-device-name.qdocinc unmount

    Then,

    \badcode
        cd <INSTALL_DIR>
        sudo dd bs=4k if=5.6/Boot2Qt/colibri-vf/images/b2qt-embedded-qt5-image-colibri-vf.img of=/dev/<device_name>
    \endcode

    By default, the Toradex Colibri VF devices boot from their internal NAND memory. In order to boot from
    an external SD card, the U-Boot needs to be modified. Connect a serial cable
    to the device and enter into the U-Boot environment by pressing any key before the autoboot.
    Enter following commands into U-Boot:

    \badcode
        run setupdate
        run update_uboot
    \endcode

    Reset or power cycle the device to continue.
    To reset the U-Boot environment to new default values, enter the following commands
    in the U-Boot command line

    \badcode
        env default -a
        saveenv
    \endcode


    New U-Boot commands are now stored into the device, and you can start \B2Q. For more information
    about the boot process on Toradex Colibri iMX6, see
    \l{http://developer.toradex.com/software-resources/arm-family/linux/linux-booting}{Toradex Linux Booting}.

    After the image has been deployed, insert the SD card, power on the device and check that
    the \B2Q welcome screen and/or demo appear.

    \section1 Using the Toradex Capacitive Multi-Touch Adapter

    It is possible to use the \l{http://developer.toradex.com/product-selector/capacitive-multi-touch-display}
    {Toradex Capacitive Multi-Touch Adapter} with \B2Q.  First follow the instuctions for setting up
    your screen \l{http://developer.toradex.com/knowledge-base/capacitive-multi-touch-display-(linux)}
    {here}.  To enable touch support for your screen in \B2Q append the following lines to /etc/appcontroller.conf and uncomment line for the VF module being used.

    \badcode
        #VF50
        #env=QT_QPA_GENERIC_PLUGINS=evdevtouch:/dev/input/event1
        #VF61
        env=QT_QPA_GENERIC_PLUGINS=evdevtouch:/dev/input/event0
    \endcode

    \section1 Setting up USB Access

    \include b2qt-post-install-setup.qdocinc setting up usb access

    \section1 Configuring a Device Kit in Qt Creator

    \include b2qt-post-install-setup.qdocinc configuring device kit

    You are now ready to start developing for your device. For more information,
    see \l{Building and Running an Example}.
*/