1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
|
/****************************************************************************
**
** Copyright (C) 2014 Digia Plc
** All rights reserved.
** For any questions to Digia, please use the contact form at
** http://qt.digia.com/
**
** This file is part of Qt Enterprise Embedded.
**
** Licensees holding valid Qt Enterprise licenses may use this file in
** accordance with the Qt Enterprise License Agreement provided with the
** Software or, alternatively, in accordance with the terms contained in
** a written agreement between you and Digia.
**
** If you have questions regarding the use of this file, please use
** the contact form at http://qt.digia.com/
**
****************************************************************************/
/*!
\target Nexus 7 (2012/2013) (embedded Android)
\page qtee-preparing-hardware-nexus-7.html
\title Preparing Nexus 7 (2012/2013)
\previouspage qtee-installation-guide.html
\nextpage qtee-building-and-running.html
Take the following steps to prepare a
\l{http://www.google.com/nexus/7/specs/}{Nexus 7 (2012/2013)} for
\B2Q.
\note The installation process will wipe the device. Make sure to
backup any personal data. The device can later be restored to
factory state, see \l{nexus-factory-reset}{Troubleshooting}.
The Nexus 7 must have the same Android main version (e.g. \c{4.2}
or \c{4.4}) as the generic \B2Q eAndroid stack that is to be
installed. If needed, you can update the Android version either by
using Android's upgrading tool, or by flashing a factory image of
the right version. See \l{nexus-factory-reset}{Troubleshooting}.
\section1 Enabling Developer Mode
In order to install the \B2Q stack into the Nexus 7, you need to
enable developer mode and USB debugging. This is only needed for
the first time install.
\note If for some reason the device does not boot up normally, it
is also possible to install to a Nexus 7 started up in
\c{fastboot} (bootloader) mode (see
\l{nexus-factory-reset}{Troubleshooting}). Just skip this section
and add the \c{-fastboot} argument to the \c{deploy.sh} command
below.
\list 1
\li Power up the device.
\li Open the \b{Settings} app and select the \b{About tablet} item.
\li Press the \b{Build number} item seven times, until the message "You are now a developer!" appears.
\li Back in the \b{Settings} menu, select \b{Developer options}.
\li Press the \b{USB debugging} item and confirm that you allow USB debugging.
\endlist
You should now be able to establish USB connection to the device as follows.
\section1 Setting up USB Access
\include b2qt-post-install-setup.qdocinc setting up usb access
\section1 Deploying the \B2Q Stack
Depending on the edition of your Nexus 7 device, use one of the
commands below to install the \B2Q stack. Replace \c{X.Y} with the
device's Android version number, for example \c{4.2} or \c{4.4}.
\note The deploy script will check that the connected Nexus device
is of the expected type and Android version, and abort the
installation if it is not.
\list
\li \b{Nexus 7 (2013):}
\badcode
cd <INSTALL_DIR>
./Boot2Qt-3.x/generic-X.Y-eAndroid/images/nexus7v2/deploy.sh
\endcode
\li \b{Nexus 7 (2012):}
\badcode
cd <INSTALL_DIR>
./Boot2Qt-3.x/generic-X.Y-eAndroid/images/nexus7/deploy.sh
\endcode
\endlist
During the installation, the device may ask for confirmation to be
unlocked. Press the power button once to confirm.
The device will reboot during the process. Do not interact with it
or unplug it until the process is fully completed.
\section1 Configuring a Device Kit in Qt Creator
\include b2qt-post-install-setup.qdocinc configuring device kit android
You are now ready to start developing for your device. For more information,
see \l{Building and Running an Example}.
*/
|
