diff options
Diffstat (limited to 'meta-boot2qt-distro/dynamic-layers/toradex-nxp-layer/recipes-qt/boot2qt-addons/qbsp-readme/mx8')
-rw-r--r-- | meta-boot2qt-distro/dynamic-layers/toradex-nxp-layer/recipes-qt/boot2qt-addons/qbsp-readme/mx8/README | 52 |
1 files changed, 52 insertions, 0 deletions
diff --git a/meta-boot2qt-distro/dynamic-layers/toradex-nxp-layer/recipes-qt/boot2qt-addons/qbsp-readme/mx8/README b/meta-boot2qt-distro/dynamic-layers/toradex-nxp-layer/recipes-qt/boot2qt-addons/qbsp-readme/mx8/README new file mode 100644 index 00000000..b1f8b744 --- /dev/null +++ b/meta-boot2qt-distro/dynamic-layers/toradex-nxp-layer/recipes-qt/boot2qt-addons/qbsp-readme/mx8/README @@ -0,0 +1,52 @@ +To successfully set up the Boot to Qt software stack, +follow the instructions in https://doc.qt.io/QtForDeviceCreation/qtdc-qbsp-installation-guide.html#. + +In 2. Installing Boot to Qt on Target Device, see also the following device specific instructions. + + +2. Installing Boot to Qt on Target Device + +To flash the image, you can use either Toradex Easy Installer +(https://developer.toradex.com/software/toradex-easy-installer#) or Qt's Flashing Wizard. + + +2.1 Flashing with Toradex Easy Installer: + +When Toradex Easy Installer is connected to the Internet, it automatically provides +the latest Boot to Qt image in its image list but that is not necessarily compatible +with your Boot to Qt installation. When you flash with Toradex Easy Installer, +you should always use the *.tezi.tar package that is included into the Boot to Qt +installation. + +Flash the Boot to Qt image with Toradex Easy Installer as follows: + +1. If your target device does not have the pre-installed Toradex Easy Installer, +follow instructions in https://developer.toradex.com/software/toradex-easy-installer#load-toradex-easy-installer# +to load Toradex Easy Installer. +2. Your Boot to Qt installation has the *.tezi.tar package under +<Qt installation directory>/<Qt version>/Boot2Qt/<target>/images. Extract the package +to an SD card or a USB flash drive. +3. Flash the image from the SD card or the USB flash drive with Toradex Easy Installer. +See https://developer.toradex.com/software/toradex-easy-installer#installing-the-images. + + +2.2 Flashing with Qt's Flashing Wizard + +1. Use the RS-232 cable to access the serial terminal on Toradex board. +2. Power on your device and press any key to stop the autoboot. +3. Run the following command in U-Boot: + +ums 0 mmc 0 + +4. Connect your device to the development host using USB On-The-Go (OTG). +5. Use Flashing Wizard to flash the image to the device: + 5.1 Launch Qt Creator. + 5.2 Select Tools > Flash Boot to Qt Device, and follow the instructions in Flashing Wizard. +6. Press Ctrl+C in the U-Boot console and run the reset command. + +Note: The u-boot is not updated when using the Flashing Wizard. + +For more information about flashing the Toradex devices, +see https://developer.toradex.com/software/linux/linux-software/build-apalis-imx8-yoctoopenembedded-bring-up-image#emmc-boot#. + +Note: The Boot to Qt software stack supports only the v1.0B silicon. |