Doc: preparing SABRE SD i.MX6Dual

Task-number: QTEE-842
Change-Id: I93b9178b201593c5c28c7e51ca16404a3509ed9f
Reviewed-by: Kalle Viironen <kalle.viironen@theqtcompany.com>

1 files changed, 84 insertions, 0 deletions

diff --git a/src/doc/src/devices/qtee-sabre-sd-imx6.qdoc b/src/doc/src/devices/qtee-sabre-sd-imx6.qdoc
new file mode 100644
index 0000000..a0a9d24
--- /dev/null
+++ b/src/doc/src/devices/qtee-sabre-sd-imx6.qdoc
@@ -0,0 +1,84 @@
+/****************************************************************************
+**
+** Copyright (C) 2014 Digia Plc
+** All rights reserved.
+** For any questions to Digia, please use the contact form at
+** http://www.qt.io
+**
+** This file is part of Qt Enterprise Embedded.
+**
+** Licensees holding valid Qt Enterprise licenses may use this file in
+** accordance with the Qt Enterprise License Agreement provided with the
+** Software or, alternatively, in accordance with the terms contained in
+** a written agreement between you and Digia.
+**
+** If you have questions regarding the use of this file, please use
+** the contact form at http://www.qt.io
+**
+****************************************************************************/
+/*!
+    \target SABRE SD i.MX6Quad (embedded Linux)
+    \target SABRE SD i.MX6Dual (embedded Linux)
+    \page qtee-preparing-hardware-imx6sabresd.html
+    \title Preparing SABRE SD i.MX6
+    \previouspage qtee-installation-guide.html
+
+    Take the following steps to prepare
+    \l {http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=RDIMX6SABREBRD}
+    {Freescale SABRE SD i.MX6} boards for \B2Q:
+    \list
+        \li Freescale SABRE SD i.MX6Quad
+        \li Freescale SABRE SD i.MX6Dual
+    \endlist
+
+    \note It is important that you repeat the steps in this section after you
+    update \SDK.
+
+    The images containing the \B2Q stack for the above devices are included
+    in \SDK, ready to be copied to an SD card.
+
+    \section1 Preparing an SD Card
+
+    An SD card of at least 1 GB capacity is sufficient.
+
+    \include detect-sd-card-device-name.qdocinc instructions
+
+    \section1 Installing the \B2Q Image
+
+    \include common.qdocinc wizard
+
+    To write the image to the SD card, ensure that no partitions on the
+    SD card are mounted:
+
+    \include detect-sd-card-device-name.qdocinc unmount
+
+    To deploy the image on \b {i.MX6Quad}, enter the following commands:
+
+    \badcode
+        cd <INSTALL_DIR>
+        sudo Boot2Qt-4.x/imx6qsabresd-eLinux/images/deploy.sh /dev/<device_name>
+    \endcode
+
+    To deploy the image on \b {i.MX6Dual}, you need to enter an additional boot
+    argument:
+
+    \badcode
+        cd <INSTALL_DIR>
+        sudo Boot2Qt-4.x/imx6qsabresd-eLinux/images/deploy.sh --uboot u-boot-imx6dlsabresd.imx /dev/<device_name>
+    \endcode
+
+    After the image has been deployed, insert the SD card, power on the device and check that
+    the \B2Q welcome screen and/or demo appear.
+
+    \section1 Setting up USB Access
+
+    \include b2qt-post-install-setup.qdocinc setting up usb access
+
+    \section1 Configuring a Device Kit in Qt Creator
+
+    \include b2qt-post-install-setup.qdocinc configuring device kit
+
+    You are now ready to start developing for your device. For more information,
+    see \l{Building and Running an Example}.
+*/
+